Last updated: 29 July 2026
This page sets out the accepted manufacturing tolerances for each of our manufacturing technologies. It forms an integral part of the Terms (Section 6), and the figures in it are the basis for assessing whether a product conforms to the order.
What is a tolerance? Every manufacturing process produces a small deviation from the theoretical dimension in the file. A deviation within the ranges specified here is an inherent part of the process and is not considered a defect. A deviation outside these ranges is — and we will repair, remanufacture or refund the payment. See Section 4 of the Cancellations & Returns Policy.
Need a tighter tolerance? In most technologies it is possible — but it requires a 2D drawing marking the required tolerance, our prior written approval, and usually an additional charge. A tight tolerance that was not agreed in advance is not binding on us.
Printed circuit boards (PCB)
| Parameter | Value | Note |
|---|---|---|
| Board dimensions — CNC routing | ±0.2 mm (standard) · ±0.1 mm (high precision) | High precision by prior arrangement |
| Board dimensions — V-scoring | ±0.4 mm | Cheaper separation method, wider tolerance |
| Board thickness (1.0 mm and above) | ±10% | A 1.6 mm board will arrive in the range 1.44–1.76 mm |
| Board thickness (below 1.0 mm) | ±0.1 mm | |
| Copper trace width | ±20% | Accepted deviation in the etching process |
| Plated hole diameter (PTH) | +0.13 / −0.08 mm | |
| Non-plated hole diameter (NPTH) | ±0.05 mm | Press-fit holes |
| Hole position | ±0.05 mm | |
| Controlled impedance | ±10% | Available on 4 layers and up, by advance order |
| Minimum trace and spacing | 0.10 / 0.10 mm | With 1oz copper; 0.16/0.16 mm with 2oz |
| Minimum hole diameter | 0.15 mm | On multilayer boards; 0.3 mm on single-layer |
| Minimum annular ring | ≥0.20 mm | 0.25 mm and above recommended |
| Silkscreen — line width | ≥0.15 mm | Thinner lines may disappear |
| Silkscreen — character height | ≥1.0 mm | Character ratio 1:6 |
| Copper-to-board-edge clearance | ≥0.2 mm (routing) · ≥0.4 mm (V-scoring) | |
| Board dimensions | Minimum 3×3 mm | Small boards — panel recommended |
| Number of layers | 1–32 |
Additional notes: Solder mask shade may vary slightly between production batches. Board warpage (bow & twist) is measured per the IPC-A-600 standard; if the board is intended for automated assembly (SMT), state this in the order. Available surface finishes: HASL (leaded/lead-free), ENIG and OSP.
CNC machining
| Parameter | Value | Note |
|---|---|---|
| Standard tolerance — without a drawing | ±0.1 mm | The default. Applies to every dimension not marked otherwise |
| Tight tolerance — with a drawing | Down to ±0.05 mm | Requires a marked-up 2D drawing and prior approval |
| Wall thickness — metal | 0.8 mm recommended (absolute minimum 0.5 mm) | Thin walls are prone to chatter and distortion |
| Wall thickness — plastic | 1.5 mm recommended (absolute minimum 1.0 mm) | |
| Internal corner radius | R = (depth ÷ 10) + 0.5 mm | The cutting tool is round — a perfectly sharp internal corner cannot be machined |
| Minimum internal corner radius | R0.5 mm at depths up to 3 mm | A smaller radius adds significant cost |
| Cavity depth | Optimal: 2–3 × tool diameter | Above 5 × diameter — high cost and requires approval |
| Thread length | ≤ 3 × hole diameter | In a blind hole, leave ≥0.5 × diameter unthreaded |
| Surface roughness — standard | Ra 3.2 | The default |
| Surface roughness — fine | Ra 1.6 | By prior arrangement |
| Surface roughness — extra fine | Ra 0.8 | On request, at an additional charge |
| Maximum dimensions | 1100 × 600 × 500 mm | |
| Minimum dimensions | 30 × 20 × 5 mm (metal) · 30 × 20 × 8 mm (plastic) | Flat part: 30 × 10 × 3 mm |
Appearance (standard grade): Light scratches up to 10 mm long, up to 5 in number, are permitted; light tool marks that do not affect function; slight shade variation between anodized parts. A fine appearance grade (up to 2 scratches 5 mm long, no tool marks) is available by prior arrangement and at an additional charge.
Anodizing and sandblasting: Rack (hanging) marks — up to 4 locations, in places that do not affect assembly. Shade variation between different production batches is possible and is not a defect. Sandblasting requires walls ≥1.5 mm due to the risk of distortion. Threads smaller than M5 are not anodized (the grit lodges in the thread).
3D printing
| Technology | Dimensional tolerance | Minimum wall thickness | Minimum hole | Max build volume (mm) |
|---|---|---|---|---|
| Resin (SLA) | ±0.2 mm up to 100 mm · ±0.3% above | 0.5–2.0 mm | Φ1.0 mm | 780 × 780 × 530 |
| Nylon (MJF) | ±0.3 mm up to 100 mm · ±0.4% above | 1.0–2.0 mm | Φ1.5 mm | 370 × 276 × 360 |
| Nylon (SLS) | ±0.3 mm up to 100 mm · ±0.4% above | 1.0–2.0 mm | Φ1.5 mm | 350 × 350 × 400 |
| Plastic (FDM) | ±0.3 mm up to 100 mm · ±0.4% above | 1.6–2.5 mm | Φ2.0 mm | 580 × 480 × 480 |
| Metal (SLM) | ±0.3 mm up to 100 mm · ±0.4% above | 1.5–2.5 mm | Φ2.0 mm | 390 × 290 × 390 |
| Full colour (WJP) | ±0.2 mm up to 100 mm · ±0.3% above | 1.0–2.0 mm | Φ1.5 mm | 380 × 330 × 230 |
Further details for 3D printing
| Parameter | Value | Note |
|---|---|---|
| Hole tolerance | Resin / Nylon: ±0.3 mm · FDM: ±0.4 mm · Metal: ±0.5 mm | For a precise hole — design it undersized and drill to size |
| Embossed or engraved detail | Resin / Nylon: 0.8 mm depth and width · FDM / Metal: 1.0 mm | Smaller text will not be legible |
| Clearance between moving parts | Resin / FDM: 0.5 mm · Nylon: 0.6 mm · Metal: 1.0 mm | Too little clearance — the parts will fuse |
| Wall thickness — depends on size | The lower value is for small parts (5×5 mm), the higher for large parts (200×200 mm) |
Appearance and finish: Visible layer lines are an inherent characteristic of 3D printing and are not a defect. In resin — support marks on the underside of the part are part of the process. In nylon — the typical surface roughness is around Ra 10–15 µm. Shade may vary slightly between batches. Large flat parts may show slight warping (on a 150×150 mm plate, up to approx. 0.5 mm has been measured).
What to do if a part is out of tolerance
If you received a product that appears to you to be outside the ranges on this page — contact us within the period stated in the Cancellations Policy, including the order number, photos and a description of the deviation, and preferably a measurement. We will check and get back to you. If the deviation is confirmed — you may choose between repair, remanufacture or a full refund including shipping charges, and the cost of the return will be borne by us.
The figures on this page reflect manufacturing capabilities as of the update date above, and may be updated. The binding version is the one published on the site at the time the order was placed.