Skip to content
עברית Order

Price a PCB without sending a single email.

Upload Gerbers, choose a spec, and the price and estimated lead time update on screen. An engineer checks every order before production.

Upload files, choose a spec and get a price.

  • 1–32Layers
    above 20 by quote
  • FR-4 to Rogers6 base materials
  • ENIG · HASL · OSPPad finishes
  • 670×600mm, 2-layer FR-4

PCB Ordering

Choose a spec, see a price. Same file, same spec — two production routes.

On this route the price is calculated on screen against the spec you chose, and you can order and pay on the site.

Gerber file

ZIP · RAR · 7Z · up to 50MB
Drag a file here, or click to select Gerber export from KiCad, Altium, Eagle or any other EDA software
The files are used for this order only.
Uploading file
0%
Starting upload
File uploaded successfully.
Board dimensionsmm — read from the file when possible
× mm
Quantity
layers
Base material
Board thicknessmm
Outer copper
Inner copper
Trace width and spacingTrace / Space
נקבע מקובצי ה-Gerber גאומטריית הנחושת שבקבצים היא רוחב המסלול והמרווח בפועל.
Material type / TG
Surface finish
Solder mask color
Silkscreen color
Via coveringVia covering
Electrical test
Gold fingersGold fingers
Castellated holesCastellated holes
Rounded cornersDeburring
Edge platingEdge plating
Outline tolerance
Production file approval
Marking on the board
Production route
Method
Cut type
Rows × columns
×
Carrier frameEdge rails
Spacing between units
Different designs in the panel
Type
Sides
Polishing
Fiducial marksFiducials
Calculating stencil price

Assembly is done from the factory's stock only. A component without sufficient stock will not be included in the order — we will show it here and suggest an available alternative in the same package.

Pick & Place file Required for ordering

The Gerber file does not contain component positions. The placement file (Pick & Place / CPL / Position) is what lets the factory know where each component goes — and thanks to it you'll see your board with the components here in 3D.

Drag the placement file here, or click to select CSV · TXT · POS — Pick & Place export from KiCad, Altium or EasyEDA
Assembly side
THT points per unitComponents with leads — hand soldering. 0 if everything is SMD
Placement approval before assemblyA component placement image is sent for your approval
Component list Still empty
The price shown is an automatic estimate and not a binding offer. The final price will be set after an engineering review of the file and sent for your approval before production; if it changes — you can approve or cancel at no charge. Items produced from a personal file cannot be cancelled after production has started, except for a defect or non-conformity. Full terms and conditions · Cancellation policy
Not sure which stackup to choose? Full stackup guide — all stackups, thicknesses and dielectric constants.

What you can order.

Some options depend on the material and the layer count. The calculator shows only what is available for the spec you chose.

Layers
Up to 20 layers in the calculator, priced on screen · 22–32 layers by quote
Base material
FR-4 · Aluminium · Copper core · Flex / FPC · Rogers · PTFE
Board thickness
0.4–2.0 mm, by layer count
Dimensions
From 3×3 to 670×600 mm in 2-layer FR-4. The limit depends on material, layer count and thickness
Copper weight
Outer 1oz or 2oz · inner 0.5oz or 1oz
Pad finish
Lead-free HASL · leaded HASL · ENIG · OSP
Solder mask colour
Green · red · blue · black · white · yellow · purple
Vias
Tented · Untented · Plugged · Epoxy filled
Panelization
V-Cut, tab routing or both
Stencil and assembly
SMT stencil, and assembly on one or both sides

What to prepare before uploading.

  • RequiredGerber and drill files.zip · .rar · .7z · 50MBExactly as they come out of KiCad, Altium or Eagle.
  • For assemblyBOM, bill of materials.csv · .txt · .tsv · .xlsxOnly if you also order assembly.
  • For assemblyPlacement file.csv · .txt · .pos · .tsvPick & Place, only if you also order assembly.

From a Gerber file to a board on your desk.

  1. Upload a fileA ZIP with Gerbers and drills.
  2. Choose the specLayers, thickness, mask and finish.
  3. Check and approveWe review the file and confirm with you.
  4. Production and shippingTo the spec you approved.

Questions before you order.

Does quantity change the unit price?

Choose a quantity in the calculator and the price updates, including the cost per unit. The spec and the file check stay the same at any quantity.

Which files do I need to send?

A ZIP with Gerber files and a drill file, as they come out of KiCad, Altium or Eagle. Dimensions and layers are read from the file, and a 3D view of the board appears on screen.

What is the difference between ENIG and HASL?

ENIG gives a flat surface that suits fine-pitch parts such as QFN and BGA. HASL costs less and suits boards with larger parts.

A question about your board?

Write to an engineer. We usually reply within one business day.