Skip to content
עברית Order

Engineering information

Specifications & Manufacturing Tolerances

On this page
  1. Printed circuit boards (PCB)
  2. CNC machining
  3. 3D printing
  4. What to do if a part is out of tolerance

Last updated: 29 July 2026

This page sets out the accepted manufacturing tolerances for each of our manufacturing technologies. It forms an integral part of the Terms (Section 6), and the figures in it are the basis for assessing whether a product conforms to the order.

What is a tolerance? Every manufacturing process produces a small deviation from the theoretical dimension in the file. A deviation within the ranges specified here is an inherent part of the process and is not considered a defect. A deviation outside these ranges is — and we will repair, remanufacture or refund the payment. See Section 4 of the Cancellations & Returns Policy.

Need a tighter tolerance? In most technologies it is possible — but it requires a 2D drawing marking the required tolerance, our prior written approval, and usually an additional charge. A tight tolerance that was not agreed in advance is not binding on us.

The part as ordered100.0 mm99.9 – 100.1 mmOut of toleranceOut of tolerance
A nominal dimension of 100 mm with a ±0.1 tolerance: any result within the green range (99.9–100.1 mm) is correct manufacturing — not a defect. Outside that range is a deviation that entitles you to a repair or refund.

Printed circuit boards (PCB)

Annular ringAnnular Ring ≥ 0.20 mmHolePTH: +0.13 / -0.08 mmW0.10 mmS0.10 mmWidth: +/-20%Actual trace width
Top view: the copper annular ring around a hole (minimum 0.20 mm), and the width (W) and spacing (S) of copper traces — minimum 0.10 mm each, with an accepted deviation of ±20% from the design.
Parameter Value Note
Board dimensions — CNC routing ±0.2 mm (standard) · ±0.1 mm (high precision) High precision by prior arrangement
Board dimensions — V-scoring ±0.4 mm Cheaper separation method, wider tolerance
Board thickness (1.0 mm and above) ±10% A 1.6 mm board will arrive in the range 1.44–1.76 mm
Board thickness (below 1.0 mm) ±0.1 mm
Copper trace width ±20% Accepted deviation in the etching process
Plated hole diameter (PTH) +0.13 / −0.08 mm
Non-plated hole diameter (NPTH) ±0.05 mm Press-fit holes
Hole position ±0.05 mm
Controlled impedance ±10% Available on 4 layers and up, by advance order
Minimum trace and spacing 0.10 / 0.10 mm With 1oz copper; 0.16/0.16 mm with 2oz
Minimum hole diameter 0.15 mm On multilayer boards; 0.3 mm on single-layer
Minimum annular ring ≥0.20 mm 0.25 mm and above recommended
Silkscreen — line width ≥0.15 mm Thinner lines may disappear
Silkscreen — character height ≥1.0 mm Character ratio 1:6
Copper-to-board-edge clearance ≥0.2 mm (routing) · ≥0.4 mm (V-scoring)
Board dimensions Minimum 3×3 mm Small boards — panel recommended
Number of layers 1–32

Additional notes: Solder mask shade may vary slightly between production batches. Board warpage (bow & twist) is measured per the IPC-A-600 standard; if the board is intended for automated assembly (SMT), state this in the order. Available surface finishes: HASL (leaded/lead-free), ENIG and OSP.

CNC machining

R = H/10 + 0.5 mmThe cutting tool is roundA perfectly sharp internal corner — impossibleWall thicknessmetal 0.8 mm · plastic 1.5 mm
The two most common limitations in CNC machining: internal corner radius — derived from the pocket depth (H = depth in mm), and minimum wall thickness — 0.8 mm in metal, 1.5 mm in plastic.
Parameter Value Note
Standard tolerance — without a drawing ±0.1 mm The default. Applies to every dimension not marked otherwise
Tight tolerance — with a drawing Down to ±0.05 mm Requires a marked-up 2D drawing and prior approval
Wall thickness — metal 0.8 mm recommended (absolute minimum 0.5 mm) Thin walls are prone to chatter and distortion
Wall thickness — plastic 1.5 mm recommended (absolute minimum 1.0 mm)
Internal corner radius R = (depth ÷ 10) + 0.5 mm The cutting tool is round — a perfectly sharp internal corner cannot be machined
Minimum internal corner radius R0.5 mm at depths up to 3 mm A smaller radius adds significant cost
Cavity depth Optimal: 2–3 × tool diameter Above 5 × diameter — high cost and requires approval
Thread length ≤ 3 × hole diameter In a blind hole, leave ≥0.5 × diameter unthreaded
Surface roughness — standard Ra 3.2 The default
Surface roughness — fine Ra 1.6 By prior arrangement
Surface roughness — extra fine Ra 0.8 On request, at an additional charge
Maximum dimensions 1100 × 600 × 500 mm
Minimum dimensions 30 × 20 × 5 mm (metal) · 30 × 20 × 8 mm (plastic) Flat part: 30 × 10 × 3 mm

Appearance (standard grade): Light scratches up to 10 mm long, up to 5 in number, are permitted; light tool marks that do not affect function; slight shade variation between anodized parts. A fine appearance grade (up to 2 scratches 5 mm long, no tool marks) is available by prior arrangement and at an additional charge.

Anodizing and sandblasting: Rack (hanging) marks — up to 4 locations, in places that do not affect assembly. Shade variation between different production batches is possible and is not a defect. Sandblasting requires walls ≥1.5 mm due to the risk of distortion. Threads smaller than M5 are not anodized (the grit lodges in the thread).

3D printing

Clearance between moving parts0.5 – 1.0 mmWithout clearance — the parts will fuseMinimum wall thickness0.5 – 2.5 mmEmbossed or engraved text0.8 – 1.0 mm
3D printing: minimum clearance between moving parts printed together, minimum wall thickness (depends on technology and size), and minimum size for embossed/engraved text.
Technology Dimensional tolerance Minimum wall thickness Minimum hole Max build volume (mm)
Resin (SLA) ±0.2 mm up to 100 mm · ±0.3% above 0.5–2.0 mm Φ1.0 mm 780 × 780 × 530
Nylon (MJF) ±0.3 mm up to 100 mm · ±0.4% above 1.0–2.0 mm Φ1.5 mm 370 × 276 × 360
Nylon (SLS) ±0.3 mm up to 100 mm · ±0.4% above 1.0–2.0 mm Φ1.5 mm 350 × 350 × 400
Plastic (FDM) ±0.3 mm up to 100 mm · ±0.4% above 1.6–2.5 mm Φ2.0 mm 580 × 480 × 480
Metal (SLM) ±0.3 mm up to 100 mm · ±0.4% above 1.5–2.5 mm Φ2.0 mm 390 × 290 × 390
Full colour (WJP) ±0.2 mm up to 100 mm · ±0.3% above 1.0–2.0 mm Φ1.5 mm 380 × 330 × 230

Further details for 3D printing

Parameter Value Note
Hole tolerance Resin / Nylon: ±0.3 mm · FDM: ±0.4 mm · Metal: ±0.5 mm For a precise hole — design it undersized and drill to size
Embossed or engraved detail Resin / Nylon: 0.8 mm depth and width · FDM / Metal: 1.0 mm Smaller text will not be legible
Clearance between moving parts Resin / FDM: 0.5 mm · Nylon: 0.6 mm · Metal: 1.0 mm Too little clearance — the parts will fuse
Wall thickness — depends on size The lower value is for small parts (5×5 mm), the higher for large parts (200×200 mm)

Appearance and finish: Visible layer lines are an inherent characteristic of 3D printing and are not a defect. In resin — support marks on the underside of the part are part of the process. In nylon — the typical surface roughness is around Ra 10–15 µm. Shade may vary slightly between batches. Large flat parts may show slight warping (on a 150×150 mm plate, up to approx. 0.5 mm has been measured).

What to do if a part is out of tolerance

If you received a product that appears to you to be outside the ranges on this page — contact us within the period stated in the Cancellations Policy, including the order number, photos and a description of the deviation, and preferably a measurement. We will check and get back to you. If the deviation is confirmed — you may choose between repair, remanufacture or a full refund including shipping charges, and the cost of the return will be borne by us.

The figures on this page reflect manufacturing capabilities as of the update date above, and may be updated. The binding version is the one published on the site at the time the order was placed.

An engineering question?

Engineering reply usually within one business day.

Ask an engineer